User Tools

Site Tools


robocore:hardware:description

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
robocore:hardware:description [2016/04/29 06:43]
radekj [Power Supply]
robocore:hardware:description [2017/03/07 19:25] (current)
zielmicha ↷ Links adapted because of a move operation
Line 3: Line 3:
 ==== RoboCORE 1.0 - top and bottom view ==== ==== RoboCORE 1.0 - top and bottom view ====
  
-{{:​robocore_bottom.jpg?​nolink&​450|}} +{{robocore:​robocore_bottom.jpg?​nolink&​450|}} 
-{{:​top.jpg?​nolink&​450|}}+{{robocore:​top.jpg?​nolink&​450|}}
  
 ==== Specification ==== ==== Specification ====
Line 17: Line 17:
 | [[SD card]] | 1 | microSD card connector | | [[SD card]] | 1 | microSD card connector |
 | [[hDBG]] | 1 | Hardware programmer/​debugger port | | [[hDBG]] | 1 | Hardware programmer/​debugger port |
-| [[hExt]] | 2 | Extension port - 9*GPIO, UART, SPI, I2C, ADC, [[hardware:EXTI]] |+| [[hExt]] | 2 | Extension port - 9*GPIO, UART, SPI, I2C, ADC, [[robocore:hardware:exti]] |
 | [[hCAN]] | 1 | CAN port | | [[hCAN]] | 1 | CAN port |
-| Wi-Fi | 1* | Wi-Fi transmitter available with Intel® [[edison:​start|Edison]] module| +| Wi-Fi | 1* | Wi-Fi transmitter available with Intel® [[robocore:edison:​start|Edison]] module| 
-| Bluetooth 4.0 | 1* | Bluetooth transmitter available with Intel® [[edison:​start|Edison]] module|+| Bluetooth 4.0 | 1* | Bluetooth transmitter available with Intel® [[robocore:edison:​start|Edison]] module|
 | [[:hLED]] | 4 | Power LED + 3 programmable LEDs | | [[:hLED]] | 4 | Power LED + 3 programmable LEDs |
 | [[:​hButton]] | 3 | ON/OFF button + 2 programmable buttons | | [[:​hButton]] | 3 | ON/OFF button + 2 programmable buttons |
-* only with Intel(R) [[edison:​start|Edison]] module+* only with Intel(R) [[robocore:edison:​start|Edison]] module
  
-See also [[:​basics#​specification|more general specification]].+See also [[robocore:​basics#​specification|more general specification]].
  
 ==== Power Supply ==== ==== Power Supply ====
Line 45: Line 45:
 RoboCORE cannot be supplied from the USB port of your laptop. Why? This is a robotic controller and has motor drivers on its board. Motors cannot be supplied from USB due to the current and voltage requirements. To avoid the risk of damaging the USB port we decided to supply RoboCORE separately. RoboCORE is designed to be programmed wirelessly and USB connection is not the basic way to program or supply the controller. RoboCORE cannot be supplied from the USB port of your laptop. Why? This is a robotic controller and has motor drivers on its board. Motors cannot be supplied from USB due to the current and voltage requirements. To avoid the risk of damaging the USB port we decided to supply RoboCORE separately. RoboCORE is designed to be programmed wirelessly and USB connection is not the basic way to program or supply the controller.
  
-How much current does it need? This strongly depends on the robot configuration. A RoboCORE without any devices connected needs up to 80mA (180mA with Intel® [[edison:​start|Edison]]). When you connect certain motors, current peaks can reach several amperes. The average current should not exceed 4 A, otherwise the overcurrent protection will be triggered and unexpected resets will occur. Remember this when you are designing your robot. ​+How much current does it need? This strongly depends on the robot configuration. A RoboCORE without any devices connected needs up to 80mA (180mA with Intel® [[robocore:edison:​start|Edison]]). When you connect certain motors, current peaks can reach several amperes. The average current should not exceed 4 A, otherwise the overcurrent protection will be triggered and unexpected resets will occur. Remember this when you are designing your robot. ​
  
 RoboCORE has two internal voltage regulators. The input voltage VIN is converted to 5 V by a switching regulator, and then to 3.3 V by a linear voltage regulator. Be aware of the current limits – the total current must not exceed 2 A through the 5 V line and 800 mA through the 3.3 V line. We will also remind you about power limitations in the description of individual interfaces. RoboCORE has two internal voltage regulators. The input voltage VIN is converted to 5 V by a switching regulator, and then to 3.3 V by a linear voltage regulator. Be aware of the current limits – the total current must not exceed 2 A through the 5 V line and 800 mA through the 3.3 V line. We will also remind you about power limitations in the description of individual interfaces.
robocore/hardware/description.1461912191.txt.gz · Last modified: 2016/04/29 06:43 by radekj